HHR Performance » Chicken Hawk Racing
Benefits of Tire Warmers
Most racers and track day riders want tire warmers to avoid cold tire crashes and to go fast right from the green flag.
It is true that these are two clear advantages of using Tire Warmers, but there are other benefits that are equally important. A Tire Warmer provides the ability to tune and manage tires in the paddock beyond the grip offered on the opening laps:
- Go Fast from the Green Flag
- Set Hot Tire Pressures in the Pits
- Avoid “cold tearing” tires
- Save “Heat Cycles” by keeping tire warm in between sessions
- Tires last longer
Hot rubber grips the track surface better since not only does the coefficient of friction increase, but the Tire’s ability to form the track surface through “mechanical keying” is increased.
Set Hot PressuresTires will increase in pressure about 20% on the track (ie: 30 to 36 psi) which makes a huge handling difference. CHR Tire Warmers will get your tires surface AND carcass into the proper temperature range (same as you’ll see on the track). Without Tire Warmers 6-8 laps would be needed to get a tire to its proper “hot pressure”. Many of the current race compound tires are “low pressure” tires with psi recommendation of around 22-24 psi. These tires are more sensitive to being at hot pressure before they work properly. Set the Tire Warmers to the temperature you anticipate seeing on the track, allow them to “heat-soak” for an hour and set the Hot Pressure. When you hit the track, there will be minimal change. Getting your Hot Tire Pressure set on the Tire Warmers gets you going right away.
Avoid “Cold Tearing” Tires
Taking a 70 degree tire and pushing it hard on the track will increase the very outer surface of the rubber in a couple of laps. However the rubber 2-3 mm down is not yet warm and not as elastic. This causes the outer rubber to grip the track surface and underlying rubber to rip or tear. This shredded look or graining once developed in the tire almost never goes away and basically ruins the tire. By pre-heating the rubber, cold tearing is simply avoided.
Save Heat Cycles
When tires are heated & then cooled, a change occurs that can be seen, measured and felt. On some tires you can actually see a blue haze form over the tire as some “oils” migrate to the surface and oxidation occurs. On other tires one might observe much drier grayish haze depending on individual tire composition. Putting the tire though these hot to cold cycles reduces the tires grip, hardens the rubber and reduces its useful life. A tire warmer can keep tires hot or simply warm (for longer periods of time) between track sessions and reduce the amount of heat cycles a tire goes through. If the tire is to see more than one track session it makes sense not to allow that tire to cool all the way to ambient; this can extend how many sessions the tire can perform at near maximum grip. By operating in this manner the tire’s grip life is increased.
Tires Last Longer
Taking tires from ambient temperature and bringing them to race temperature on the track may take from 3-6 minutes depending on the machine, track and rider. Aside from giving up speed during these opening laps, it is truly too fast to heat the tire in an ideal manner. For example on a 75 degree day, the rider gets the tire surface hot in 4 laps, which takes 6 minutes. This increase of 100 degrees in such a short amount of time actually “heat shocks” the tire. Race compound tires have several “activator” chemicals in them and get set into motion with heat. Getting the tire hot quickly actually spends or wastes some of the chemicals and tires will lose grip sooner than if warmed slowly on a warmer.
Chicken Hawk Racing manufactures Tire Warmers branded for Dunlop, Michelin and Bridgestone motorcycle tires and works closely with the tire engineers to ensure the ramp up of heat meets the tires needs.With Their close working relationship with World Superbike team Ten Kate Honda and working with various teams within Moto 2 Develeopment never stops and their products always improve
Chicken Hawk Racing Categories
Chicken Hawk Racing Products
The company known for keeping your tires warm also offers a product to keep your fuel cool. The CHR Cool Tank Covers are designed to reflect sunlight while insulating your fuel tank and include built-in pockets to accommodate flat cooling gel packs.
Fuel left out on a hot day will allow combustible compounds to evaporate which reduces horsepower. Cooler fuel means more power and cooler running engines.
Note: Designed to fit most late model sportbikes and supermotos.
Easy to install neoprene wraps install over your tire warmers and wheels to fight wind and assist heat-up on colder days. Front wrap utilizes heavy duty zippers to wrap over fender. Attain hot pressure with your warmers even on the coldest days.
Fits most sportbike and supermoto front and rear tires.
Sold in sets of two.
Note: Image for reference only. Actual Chicken Hawk Racing Wheel Insulators will vary slightly.
Melt-Proof inner liner with heat sensitive dye
Dupont Nomex/Kevlar Insulation to retain heat and heat the entire carcass deep down
Tough Codura Exterior with high impact temperature controllers
Neoprene Sides designed to keep heat close to the rim
Additional layer of insulation
Aluminized Kevlar exterior for added heat retention
Higher temperature of 195F on the Standard model and for High Setting on the 3-Temp Pole Positon
This guard not only prevents the riders breath from fogging up visor, but ALSO his Glasses.
Fog Buster Breath Guard with the following features:
- Comfortable Neoprene construction
- Adjustable Clip for bridge of the nose
- Fits almost all full face helmets
- One Size fits all
- Available in Red, Blue & Black
Melt-Proof inner liner (with heat sensitive dye to show mis-use or mal-function)
Operating Light- RED shows when heating and GREEN when full temp is reached
Dupont Nomex/Kevlar Insulation to keep the heat in and set Hot Pressures- Heat the entire carcass deep down
Built Tough – Codura Exterior & high impact temperature controllers, full coverage Heating Elements
QUALITY & PRICE – designed & built in the USA, these warmers are 2nd to none and is one of the most economically priced!
Built and serviced in house