HHR Performance » 2014

Description: Sprint Filter P08 BMW S1000R/RR/XR HP4 (09-18)
Reinforced polyurethane frame to aid installation
Single layer polyester
P08 material currently used in MotoGP and WSBK
Innovative polyester material allows for consistent airflow
Steel wire mesh with epoxy varnish finish
Optimized filter surface area provides more airflow, more power and more filtration
Increased air permeability and filtration efficiency when compared to cotton air filters
Airflow: 5,050 l/m2/sec. / Filtration: 80?m
Can be cleaned using only compressed air
Dry filter, no oil treatments required
Direct OEM replacement
1 year warranty

Description: Sprint Filter P08 F1-85 YZF-R7 2022
Reinforced polyurethane frame to aid installation
Single layer waterproof polyester
P08 F1-85 material currently used in MotoGP and WSBK
Highest existing permeability of any air filter on the market
Innovative polyester material allows for consistent airflow
Steel wire mesh with epoxy varnish finish
Patented PTFE (Teflon™) treatment creates a waterproof barrier
Optimized filter surface area provides more airflow, more power and more filtration
Increased air permeability and filtration efficiency when compared to cotton air filters
Airflow: 15,000 l/m2/sec. / Filtration: 85?m
Can be cleaned using only compressed air
Dry filter, no oil treatments required
Direct OEM replacement
1 year warranty

Description: Stealth Ducati 1199 Panigale/S/S Tricolore (2012 - 14) / 899 Panigale ABS (2013 - 15) BSS041 From racing experience and aeronautical inspiration comes the Rizoma Stealth Mirror. Specifically designed for sport bikes. It consists of a fixed part, which fits directly to the fairing, and a movable part, which acts as a mirror glass holder. Thanks to a rotating system the two parts get aligned so in the closed position the mirror becomes an aerodynamic foil Wing! Made of billet aluminum, it has a convex glass surface to provide a wider viewing angle and is available in three different anodized colors. Flip it up to ride, flip it down when you race or if your parked up at bike night!

Description: Suter Racing Suterclutch Ducati "Clutch (WITHOUT outer basket & plate package, modellist above) 004-28004

• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Suterclutch Ducati all models with starter racks 004-28027

• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Suterclutch Honda CBR-1000RR 08-19 004-11006

• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Suterclutch Kawasaki ZX6R (636) 2013-2020 004-46003


• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Suterclutch MV-Agusta F4 1000R/R1+1/SENNA/1078/312R/Brutale 1078/Brutale 990/1090 2006-2018 004-36002

• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Suterclutch Triumph 675 daytona/675 street triple/street triple r 2006-2017 004-48002

• First choice for more than 20 years in WSBK, MotoGP & MXGP championships
• The BTL (Back Torque Limiter) slipper clutch has been designed and developed to allow traction to be adjusted to accommodate different riding conditions. The Suter Clutch reduces the threat of over-revving the engine and maximizes the suspension performance.
• Quick off the start line due to a better clutch control
• Smoother braking phase over big bumps
• Less power required to operate the clutch
• Proven faster lap times
• More precise corner entry
• Higher corner speed
• Adjusted in conjunction with chassis and suspension set up the slipper clutch encourages smooth deceleration into corners and controlled acceleration out of corners.
• Anti hopping (basic principle): Prevents locking of the rear wheel during the coupling process and thus the loss of traction
• Produces a significantly softened braking phase before corners
• The Anti-hopping effect can be adjusted for every riding style; for tuned models, there is a range of harder main springs available to order. Included with delivery are all the relevant parts for installation, plus two additional Anti-hopping springs.
• The SuterClutch is highly impressive through its excellent responsiveness, the efficient inner lubrication, and its easy installation. The unique color of this clutch results from the hard-anodized Teflon coating, which considerably minimizes the wear on the friction surfaces.
• Fully adjustable to personal riding style
• There are two editions for the SuterClutch available: The MX-Line and the BTL-Line. Unlike the BTL-Line, the MX clutch comes without the anti-hopping mechanism.
• Through its ingenious design, you can fit it without any special installation tools. The pressure plate is installed using 6 bolts, allowing easy access for maintenance.
• Quick to install without special tools

Description: Suter Racing Swingarm BMW S1000RR 2019 - 2020 041-62001
The Suter swingarm boosts performance, gives more edge grip, confidence, and feel. Your bike will be faster and safer. It makes yours like a Factory one. The swingarm comes with all you need: Axis, mud-guard,etc.

Due to the modified design, a larger tire radius/diameter can be installed, and yet there are more adjustment possibilities! Also, the changed stiffness ensures better rideability of the motorcycle and more mechanical grip, especially when exiting the corner.

Note:

• Rear shock has to be modified for the use with this swingarm (lower fixing and length).
• Routing of the exhaust system has to be adapted to the new swingarm design. The exhaust is available as an additional part.
  
• For mounting the Suter Swingarm, the assembly kit is needed.

More confidence, more feel, more fun, faster, and safer!

Description: Techspec GRIPSTER C3 SEAT PAD, KAWASAKI, ZX6R, (09-18), CARBONIN RACE TAIL; INCLUDES 3 TAIL PADS 62-5032-C3

Exclusively created by Techspec for Carbonin Bodywork Tail units!

Description: XLine2 kit tank wrap for YAMAHA R6 (2008 - 2016) XLine2 Tank Grips: Free Center Tank Protector 6 Included

Description: Thermal Heat protection for fuel tank
Teknofibra Heat shield material is designed to keep any radiant temperature from the engine or exhaust from heating up the fuel in the tank.
Cooler fuel = better performance.
Heat is the enemy when it comes to robbing power.
Its not just only the water temperature that you need to keep cool for optimum performance, Keeping your fuel cool produces the best power and why spend that extra money on race fuel if it is not staying cool.
Ever wonder why teams keep their fuel in fridges or on ice? add it at the last minute? Not to mention when it heats up it expands and it could be the difference of fitting that last 1/8th of a gallon in to finish that race!

These kits come pre cut to fit your model motorcycle , all you need to do is remove any factory heat sheild material clean with a degreaser and install your Teknofibra material , It really is simple.

This material is thinner and lighter than the material that comes from the factory which is a mineral based fiber.
Teknofibra is unlike anything else and will not burn or catch fire, it is non toxic and has proven to keep fuel temps up to 48degrees F cooler than oem material

Technical partner of JIR, Teknofibra® has long been known in the industry and used by prestigious Moto2, World Superbike, CIV and many others teams, for the following applications:

Protection of fairing and belly positioned in close proximity of the exhaust pipes.
Interposed between air box and throttle body allows the aspiration of cold air.
Glued under the tank keeps the lower the fuel temperature.
It maintains a stable temperature of the gas /oil on the nitrogen tank bladder of the dampers installed near the exhaust pipes.
Protects the battery and wiring avoiding problems to the ECU.
Protection of electronic components in hot areas.
Under the saddle and the cowl cover It protects the rider from the heat transmitted from the engine and the exhaust system.
More generally, to solve any problem of heat.

Description: TIGHTAILS APRILIA RSV4 09'+ UPPER FAIRING STAY APRRSV4UPP

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS BMW S1000RR 09-18' SUBFRAME BMW1000SUB

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS DUCATI PANIGALE 11-17' SUBFRAME DUCPANSUB

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS HONDA CBR1000RR 08-15' UPPER FAIRING STAY HON1000UPP

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS KAWASAKI ZX10 11-15' UPPER FAIRING STAY KAWZX10UPP

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS SUZUKI GSXR 600/750 11'+ REAR SUPPORT BRACKET SUZ6001BRA

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.

Description: TIGHTAILS SUZUKI GSXR1000 09-16' REAR SUPPORT BRACKET SUZ1009BRA

Tightails is made for racing only. They are not designed for use with Street/OEM Bodywork. Tightails is made for race bodywork which do not have headlights, tail lights, mirrors, etc.